SPOT(MoveType, POINT_DATA, SGEQ_ParamData, SGRS_ParamData) 焊接控制時序

DEF SPOT (MoveType:IN, PointData:IN, SGEQ_ParamData:IN, SGRS_ParamData:OUT )

MoveType:移動類型? PTP

PointData: 焊點的數據:

SG_POINT_Default={Name[]"SG1",GNumber 1,Thickness 0.0,ThicknessTol 0.0,ForceProfile[]"none",ForceMode #SINGLE,Force 0.0,WeldTime 0.0,Force2 0.0,Comp#NO,Path 2.30000,PrNumber 1,MoveApprox TRUE,MaxRestart 5,Cont#NO,KeepForceAtWelding FALSE}

SGEQ_ParamData: 平衡控制的數據

CASE #MEDIUM

EEQ_PAct.MODE = EQMode

EEQ_PAct.TimeExpectedFactor = 75

EEQ_PAct.Push_ThresholdFactor = 100

EEQ_PAct.Push_ReduceTorqueFactor = 100

SGEQ_StartForceFactor =100

SGRS_ParamData: 暫時不用

SPOT準備點:

retry = FALSE 初始化變量重試功能

IF(SG_MaxRestart== 0)THEN SG_MaxRestart=3

SG_MaxRestart = ServoGun[1].MaxRestart=3重復次數

RetryMaxReached = TRUE ?重試達到的最大

ELSE

RetryMaxReached = FALSE

ENDIF

NewStart = FALSE

SpotSteps=checkwear ?檢查磨損步

REPEAT? 開始執行循環

IF((retry) AND (SpotSteps == endSpot))THEN

重試功能被激活, SpotSteps == endSpot在結束步

RetryMaxReached = SpotCountRetry()重復計數重試>3重試達到的最大

SpotSteps = checkwear 去檢查磨損步

retry = FALSE 關閉重試

ENDIF

SWITCH SpotSteps

CASE checkwear 檢查磨損

SGL_HandleCheckWear(SGL_CheckWear(), SpotSteps, checkNoPartIn, checkNoPartIn, 0, endspot, errorRetry, RetryMaxReached)

檢查電極是否滿足要求,正常情況去下一步checkNoPartIn

IF(SpotSteps == errorRetry)THEN? 如果需要去錯誤重試步

retry = TRUE ?激活重試

ENDIF

CASE checkNoPartIn 檢查沒有零件

IF(ServoGun[SG_ActiveGunNumber].CompType == #AIR)THEN

設置規定CompType #EQUALIZING平衡技術,因此這段程序不執行

SG_DECL_COMP_INTERRUPT (PointData.Comp,PointData.Cont)

ENDIF

IF(SGL_ReadIn(SG_NoPart,FALSE))THEN

SG_NoPart=0, 讀入E0=0,檢驗位SGL_ReadIn反饋false

SG_NoPart_ER = TRUE

SG_MainErrorHandlTyp = #MainWithNotify

returnUnused = SGE_MainAndSubmitMsg_ER (FALSE)

SpotSteps = reposition 去返回原位

ELSESGL_ReadIn反饋false執行下一步檢查槍力

SpotSteps = checkGunForceLim 執行下一步檢查槍力

ENDIF

CASE checkGunForceLim 檢查槍力極最小限值

CONTINUE

IF(NOT ((SG_GunForce)<=$FORCE_LIM[(6+SG_ExtaxActive)]))THEN

SG_ExtaxActive=1 激活的外部軸1$FORCE_LIM 力最小極限值,這段的意思是給入的力值不能小于系統極限值.

SpotSteps = checkGunForceMax去檢查力是否超出最大值

ELSE? 如果小于最小值

SG_ForceLowerFlim_ER=TRUE ?小于最小值故障報警

SG_MainErrorHandlTyp = #MainWithDlg

SpotSteps =SGL_DlgAnsOrMsgLineSel(FALSE, reposition,,RetryMaxReached)? ?需要跳到回到原位步

ENDIF

CASE checkGunForceMax? 檢查槍力是否超出最大值

CONTINUE

IF(NOT ((SG_GunForce)>$FORCE_MAX[(6+SG_ExtaxActive)]))THEN

SG_ExtaxActive=1 激活的外部軸1$FORCE_MAX 力最大極限值,這段的意思是給入的力值不能大于系統極限值.

SpotSteps = checkSpinTime 去檢查旋轉時間步

ELSE?? 否則

SG_ForceHigherFmax_ER=TRUE大于最大值故障報警

SG_MainErrorHandlTyp = #MainWithDlg

SpotSteps = SGL_DlgAnsOrMsgLineSel (FALSE, reposition,,RetryMaxReached)需要跳到故障復位步

ENDIF

CASE checkSpinTime ;檢查旋轉時間-機器人旋轉選項已啟用(機器人沒有使用此功能)

IF(SG_RobospinInstalled) AND SGRS_Active AND NOT (SGRS_ParamData.SpinTyp== #OFF)THEN

SG_RobospinInstalled=FALSE 控制器沒有安裝機器人旋轉.因此以下程序很多將不執行.

IF(SGRS_ParamData.SpinAngle == 0)THEN

SGRS_ParamData.SpinTyp = #OFF

SGRS_AngleZero_ER = TRUE

SG_MainErrorHandlTyp = #MainWithNotify

returnUnused =SGE_MainAndSubmitMsg_ER (FALSE)???

ENDIF

IF((SGRS_ParamData.SpinTimeSource == #WELDTIMER) AND (SGRS_ParamData.SpinTyp== #DURING))THEN

SGRS_ParamData.SpinTime = 0

FOR i = 1 TO(SG_ForceCountMax-1);多力驗證

IF(SG_PointForcesTime[i] < 10)THEN;檢查時間是以秒還是毫秒為單位?????????? SG_PointForcesTime[i] =SG_PointForcesTime[i] * 1000

ENDIF

SGRS_ParamData.SpinTime =SGRS_ParamData.SpinTime + SG_PointForcesTime[i]

ENDFOR

SGRS_ParamData.SpinTime =SGRS_ParamData.SpinTime + SGRS_ParamData.TimeOffset

IF NOT (SGRS_ParamData.SpinTime < 0 )THEN

SpotSteps =ActivateTorqSafety

ELSE

SGRS_TimeToLow_ER=TRUE

SG_MainErrorHandlTyp = #MainWithDlg

SpotSteps =SGL_DlgAnsOrMsgLineSel (FALSE, reposition,,RetryMaxReached)

ENDIF?????

ELSE

SpotSteps =ActivateTorqSafety

ENDIF

ELSE? 如果沒有使用運轉功能就去下一步“啟動焊接安全”

SpotSteps = ActivateTorqSafety

ENDIF?

CASE ActivateTorqSafety?啟動焊接安全

SGL_TorqueOn ()? 扭矩檢查扭矩，用以保護槍設置極限機器人扭矩值

SpotSteps = resetCompensation 去重置補償步

CASE resetCompensation?重置補償,跳過

IF(ServoGun[SG_ActiveGunNumber].CompType== #AIR)THEN

SGL_SetCompOut(TRUE,PointData.Comp) CompType=#EQUALIZING平衡技術

ENDIF

SpotSteps = PrepareMoveToForce 去準備移至力值步

CASE PrepareMoveToForce?準備移至力值

CONTINUE

INTERRUPTDECL SG_Interrupt21 WHEN $SG_PART_DETECTED[6+SG_ExtaxActive] == TRUE DO SG_SetPartDetected()

激活中斷零件檢測, $SG_PART_DETECTED[7]外部軸7軸的零件檢測,被認為檢測到零件

SG_PartDetected= FALSE零件檢測

SGL_SaveSetSoftend (SG_PartThickness-SG_PartThicknessTol)

SG_ConstSpeed=SGL_SPEED_CALC(SG_GunForce,MoveType,TRUE)

速度計算(焊鉗給入力值,運動類型PTP, 激活)

SGM_CALCULATE_POINTS(SG_GunForce,#WELD) 點計算和設定最大扭矩

IF SG_DEBUG_MeasureForce THEN

returnUnused = SGL_ForceMeanVal(TRUE)

ENDIF

SpotSteps = MoveToForce

CASE MoveToForce? 移動到力量

IF(SG_ForceTraceEnable)THEN強制跟蹤沒有啟用SG_ForceTraceEnable=FALSE

SG_StartForceTrace(SG_ActiveGunNumber)啟動力追蹤

ENDIF

SG_StopReaction = FALSE?停止反應

-------開啟中斷----------

INTERRUPTON SG_Interrupt1? ; 禁止重新定位

INTERRUPTON SG_Interrupt9 ; 停止按鈕

INTERRUPTON SG_Interrupt21 ; 檢測分割

SG_ReposActive = FALSE 重復定位不啟動

SGM_MOVE_TO_FORCE(SG_GunForce, MoveType, #WELD, SGEQ_ParamData, SGRS_ParamData)? 移動到焊接軌跡點并帶力移動進行夾緊

SGL_MaintenanceCounter(SG_ActiveGunNumber)維護計數器

SpotSteps = WaitPartDetected? 等待零件檢測到給到下一步

SGL_TimerControl(SG_TimerFCTRL,#TRestart)? 開啟時間監控

CASE WaitPartDetected? 等待零件檢測到

IF((SGEQ_ParamData.MODE<>#OFF) AND (SGEQ_Active==TRUE) AND SGEQ_ActivePointCond)THEN

SGEQ_ParamData.MODE = EQMode,平衡控制激活,活動點號SGEQ_ActivePointCond=FALSE

IF(($TIMER[SGEQ_TimerFixPos] * 0.001)> SGEQ_CurrentParameters.TIME_EXPECTED)THEN

SGEQ_StartFreeze = TRUE? 開始凍結

ENDIF

ENDIF

IF(SG_PartDetected)THEN 如果檢測到零件,通過中斷程序檢測零件

SpotSteps = ContPosChckFandThick 去檢查厚度步

ELSE? 如果沒有檢測到零件

CONTINUE

IF(($MODE_OP == #T1) OR? ($OV_PRO < 50))THEN

TimeResult =SG_TimeoutTimePartDetec * 5.0

SG_TimeoutTimePartDetec 1750.0

ELSE 如果不是T1模式,速度沒有小與50

TimeResult =SG_TimeoutTimePartDetec

ENDIF

---超時報警-----

IF($Timer[SG_TimerFCTRL] >= TimeResult)THEN

如果T33>=1750.0/875

SG_NoPartDetected_ER = TRUE 沒有找到零件故障

SG_MainErrorHandlTyp = #MainWithDlg 手動復位報警提示

$FORCE[(6+SG_ExtaxActive)] = 0 ;力控制關閉

SGEQ_StartFreeze = TRUE

SGEQ_Stop()焊鉗移動關閉

IF(NOT RetryMaxReached)THEN 如果沒有達到最大重復次數

SWITCH( SGE_MainAndSubmitMsg_ER(RetryMaxReached))

CASE 1?? 通過提示信息反饋,是要重焊,還是去下一點

是->重試最后一點

SpotSteps = errorRetry 去錯誤重試步

retry = TRUE

CASE 2; 不->繼續開槍->下一點

SpotSteps = disableForceMode 去關閉力模式

ENDSWITCH

ELSE 如果沒有到達最大重復步,就去

SpotSteps = SGL_DlgAnsOrMsgLineSel (false, disableForceMode,,RetryMaxReached)監控計算步

ENDIF

ELSE如果沒有超時就再去等待零件檢測步

SpotSteps = WaitPartDetected

ENDIF

ENDIF

CASE FastVectorMoveOff?快速矢量移動關閉步

ActivateFastVMVOff()? 確認焊接快速夾緊

SpotSteps = ContPosChckFandThick 連續位置檢查零件厚度

CASE ContPosChckFandThick??連續位置檢查零件厚度

SG_TriggerEnd=FALSE?? 觸發結束

IF(SGM_ChkForcePartThick(SGEQ_ParamData,TRUE,RetryMaxReached))THEN?? 如果計算零件厚度正確

SpotSteps = ForceReached 去力達到

ELSE 如果厚度不正確

SG_MainErrorHandlTyp = #MainWithDlg 需要手動復位

CONTINUE

IF(($MODE_OP == #T1) OR ($MODE_OP == #T2))THEN

CONTINUE

$FORCE[(6+SG_ExtaxActive)] = 0 ;關力控制

ENDIF

IF(NOT RetryMaxReached)THEN 如果沒有到達力重復最大值

SWITCH( SGE_MainAndSubmitMsg_ER(RetryMaxReached))

主要并提交故障信息

CASE 1?? ; 是->重試最后一點

SpotSteps = errorRetry

retry = TRUE

CASE 2? ;否->繼續開槍->下一點

SpotSteps = disableForceMode去關閉力模式步

ENDSWITCH

ELSE 如果可以計算步信息

SpotSteps = SGL_DlgAnsOrMsgLineSel (false, disableForceMode,,RetryMaxReached)

ENDIF

ENDIF

CASE ForceReached力達到

IF SG_DEBUG_MeasureForce THEN ?測量力診斷暫時不用

returnUnused = SGL_ForceMeanVal(FALSE)

ENDIF

IF( SGW_PrepAndStartWeld(#WaitForReady,NewStart)== 1 )THEN

開始焊接 ,焊接結束后

SpotSteps = detectWeldEnd檢測焊接結束

ELSE 如果焊接不合格

SG_TimerErrorHandlTyp = #TimerWithDlg 故障報警類型

CONTINUE

IF(($MODE_OP == #T1) OR ($MODE_OP == #T2))THEN

如果是在T1模式或者T2模式

CONTINUE

$FORCE[(6+SG_ExtaxActive)] = 0 ;關力控制

ENDIF

SGEQ_Stop() 關閉焊鉗平衡移動

;水位檢查

error_Water =SGE_WaterguardChecker()流量檢測

IF(NOT RetryMaxReached)THEN 如果沒有重試達到的最大值

IF error_Water THEN? 水錯誤

Result =SGE_MainAndSubmitMsg_ER(RetryMaxReached)

進入機器人故障提示對話框報錯: 重試達到的最大

ELSE

Result =SGE_WeldTimerMsg_ER(RetryMaxReached)

ENDIF

SWITCH Result

CASE 1?? ; yes -->重試

returnUnused = SG_ResetError_IWT(#ResetDefault)恢復默認

SpotSteps = errorRetry? 去故障重試步

retry = TRUE

CASE 2; no -->繼續開槍->下一點

returnUnused = SG_ResetError_IWT(#ResetDefault)恢復默認

SpotSteps = disableForceMode

ENDSWITCH

ELSE

SpotSteps = SGL_DlgAnsOrMsgLineSel ((NOT error_Water), disableForceMode,,RetryMaxReached)

ENDIF

ENDIF

CASE detectWeldEnd 檢測焊接結束

SG_WriteLogbook(SG_ProgramNumber, FALSE, SGEQ_ParamData)寫日志書

IF(SG_RobospinInstalled AND (SGRS_ParamData.SpinTyp==#DURING) AND SGRS_Active)THEN;SG_RobospinInstalled=false機器人運行, SpinTyp= #OFF SGRS_Active=TRUE 不使用機器人旋轉

IF SGEQ_ActivePointCond THEN

IF $VMSTATE.ACTIVE THEN

SGEQ_STOP()??????????????

WAIT FOR ($VMSTATE.ACTIVE ==FALSE)????

ENDIF??????????????

ENDIF??????????????

SGRS_RoboSpinTurn($POS_ACT_MES,MoveType, PointData, SGRS_ParamData) ;開始機器人旋轉的轉彎運動

TimerResult = SGg_ResultWeldEnd

NewStart = SGg_NewStart

ELSE? 不使用機器人旋轉就執行下面的程序

TimerResult = SGW_GetWeldEndSignal(NewStart)E785焊接完成FK

獲取焊接結束信號(重新開始)

ENDIF

IF( TimerResult == 1)THEN? ;焊接控制器無錯誤

RoboSpinBySPS = FALSE ?機器人旋轉

RoboSpinBySPS = SGL_ReadIn(SG_StartRoboSpin,TRUE)

SG_StartRoboSpin=0 ,沒有使用機器人旋轉????

IF(SG_RobospinInstalled AND (SGRS_ParamData.SpinTyp==#AFTER) ANDSGRS_Active AND RoboSpinBySPS)THEN(不使用)

-焊接后機器人旋轉-SG_RobospinInstalled=FALSE SpinTyp= #OFF ,SGRS_Active=TRUE,RoboSpinBySPS = FALSE

IF(SGRS_AktCounter[SG_ActiveGunNumber] <= SGRS_TurnCount)THEN

SGRS_HelpGunForce =((100-SGRS_ParamData.PercentForce)/100)* SG_GunForce

SGRS_GunForce =SGRS_HelpGunForce

IF(SGRS_GunForce < $Force_LIM[6+SG_ExtaxActive])THEN

;目標力小于力的極限值

SGRS_GunForce = $Force_LIM[6+SG_ExtaxActive]+1

SGRS_ForceLim_ER = TRUE

returnUnused = SGE_MainAndSubmitMsg_ER (FALSE)

ENDIF

$FORCE[(6+SG_ExtaxActive)] = SGRS_GunForce ?旋轉力760

PTP $POS_ACT? 執行當前位置

waitfor TRUE

IF SGEQ_ActivePointCond THEN

IF $VMSTATE.ACTIVE THEN

SGEQ_STOP()??????????????

WAITFOR($VMSTATE.ACTIVE == FALSE)????

ENDIF??????????????

ENDIF??????????????

SGRS_RoboSpinTurn($POS_ACT_MES,MoveType, PointData, SGRS_ParamData);開始RoboSpin的轉彎運動

SGRS_RoboSpinSetOpenPos()

IF($MODE_OP == #AUT) OR ($MODE_OP== #EX)THEN

SGRS_AktCounter[SG_ActiveGunNumber] = SGRS_AktCounter[SG_ActiveGunNumber] + 1

ENDIF

ENDIF????

ENDIF??????

焊接合格后:去禁用力模式步

SpotSteps = disableForceMode, disableForceMode=140去禁用力模式步

IF(SG_RobospinInstalled AND (SGRS_ParamData.SpinTyp==#DURING) AND SGRS_Active)THENSpinTyp=OFF 機器人旋轉暫時沒有使用

; 焊接計時器沒有錯誤，將新的起點設置為打開噴槍

SGRS_RoboSpinSetOpenPos()

ENDIF

ELSE焊接控制器錯誤,焊接不合格

SG_TimerErrorHandlTyp = #TimerWithDlg

SGEQ_Stop()?? 關閉平衡控制

IF(NOT RetryMaxReached)THEN

SWITCH( SGE_WeldTimerMsg_ER(RetryMaxReached))

CASE 1?? ; 是，重試地點，并帶有新的槍口關閉功能

SpotSteps = errorRetry? 去錯誤重試步

retry = TRUE

returnUnused = SG_ResetError_IWT(#ResetDefault)

CASE 2?? ; 不->繼續開槍->下一點

returnUnused = SG_ResetError_IWT(#ResetDefault)

SpotSteps = errorRetry

retry = FALSE

CASE 3?? ?僅重試焊縫而無需打開和關閉

returnUnused = SG_ResetError_IWT(#ResetWithRetry)

SpotSteps = ForceReached

DEFAULT

REPEAT

MsgNotify("Unexpectedanswer from weld timer, program running must be stopped.")焊接計時器的意外應答，必須停止程序運行

HALT

UNTIL FALSE

ENDSWITCH

ELSE

SpotSteps =SGL_DlgAnsOrMsgLineSel (TRUE, disableForceMode,,RetryMaxReached)? ---計算步去力關閉步

ENDIF

ENDIF

CASE disableForceMode 關閉力模式

IF(SG_PointDataAct.KeepForceAtWelding)THEN

KeepForceAtWelding=FALSE保持焊接力

RESET_TORQUE_LIMITS(6+SG_ExtaxActive)復位扭矩極限E1焊鉗

waitsec 0.0

ENDIF

CONTINUE

$FORCE[(6+SG_ExtaxActive)] = 0 ;關斷力控制

CONTINUE

;$APO.CPTP=1

INTERRUPTOFF SG_Interrupt1? ; 禁用抑制重新定位

INTERRUPTOFF SG_Interrupt9 ; 停止按鈕

INTERRUPTOFF SG_Interrupt21

SpotSteps = reposition?去回到原位步

CASE errorRetry? 錯誤重試

INTERRUPTOFF SG_Interrupt1? ; 禁用抑制重新定位

INTERRUPTOFF SG_Interrupt9 ; 停止按鈕

INTERRUPTOFF SG_Interrupt21

$FORCE[(6+SG_ExtaxActive)] = 0 ;關斷力控制

IF(SG_PointDataAct.KeepForceAtWelding)THEN

保持焊接力KeepForceAtWelding =false

RESET_TORQUE_LIMITS(6+SG_ExtaxActive)重置扭矩極限

waitsec 0.0

ENDIF

TRIGGERWHENDISTANCE= 1 DELAY= 0 DO SGL_ResetSoftEnd(SG_ActiveGunNumber)PRIO=-1

因?yàn)橛泻附庸收?重新移動到打開位置

IF((ServoGun[SG_ActiveGunNumber].CompType==#EQUALIZING) AND (SGEQ_ParamData.Mode<>#OFF) AND (SGEQ_Active==TRUE))THEN

CompType=#EQUALIZING使用平衡控制. MODE = EQMode,平衡控制激活

SGEQ_Stop();如果上次嘗試仍將其關閉，請關閉矢量移

SGL_MoveToPos(SGEQ_StartPoint,SGEQ_StartPoint,#NO,#SG_LIN)

ELSE

SGL_MoveToPos(P_APPROX,P_APPROX,#NO,MoveType)

ENDIF

----X軸沒有補償

IF ServoGun[SG_ActiveGunNumber].XCompActive THEN? XCompActive=FALSE

SWITCH MoveType

CASE #SG_PTP, #SG_LIN ,#SG_CIRC

SGL_MoveToPos(SG_Startpoint,SG_Startpoint,#NO,#SG_LIN)

CASE #SG_SPTP, #SG_SLIN ,#SG_SCIRC

SGL_MoveToPos(SG_Startpoint,SG_Startpoint,#NO,#SG_SLIN)

ENDSWITCH

ENDIF

SpotSteps = reposition?去回到原位

CASE reposition? 回到原位

SGL_TorqueOff()? 轉矩控制關閉

IF((ServoGun[SG_ActiveGunNumber].CompType==#EQUALIZING) AND (SGEQ_ParamData.Mode<>#OFF) AND (SGEQ_Active==TRUE))THEN

SGEQ_Stop();停止焊槍平衡控制.如果上次嘗試仍將其關閉，請關閉向量移動

ENDIF

IF(ServoGun[SG_ActiveGunNumber].CompType == #AIR)THEN

焊鉗平衡控制不使用空氣控制 CompType==#EQUALIZING

SWITCH SG_ExtaxActive

CASE 1

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E1>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E1<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

CASE 2

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E2>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E2<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

CASE 3

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E3>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E3<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

CASE 4

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E4>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E4<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

CASE 5

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E5>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E5<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

CASE 6

IF(SG_ClosingAxDir<0)THEN

IF($AXIS_ACT.E6>=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()???????????????????

ELSE???????????????????????????????????

INTERRUPTON SG_Interrupt11

ENDIF

ELSE??

IF($AXIS_ACT.E6<=SG_TriggerCompPos)THEN

SGL_COMPENSATOR()

ELSE

INTERRUPTON SG_Interrupt11

ENDIF

ENDIF

ENDSWITCH

ENDIF

SpotSteps = endSpot?步結束

ENDSWITCH

UNTIL((SpotSteps == endSpot) AND ((retry == FALSE) OR (RetryMaxReached)))

結束循環控制的條件: 在結束步并且沒有重復,或者重復次數達到最大值

編輯：黃飛

?