高穩定100KHz時鐘發生電路,100khz clock generator
高穩定100KHz時鐘發生電路,100khz clock generator
關鍵字：高穩定100KHz時鐘發生電路
Build A 100Khz Crystal Calibrator
By N1HFX
There is a great deal of old amateur gear which many amateurs have decided to restore and bring back to life. While much of the early amateur transceivers work just fine they usually lack a digital readout and must rely on analog dials for tuning. The problem of dial calibration is complicated by the non-linear effects of tuning capacitors. This month's circuit is a 100Khz crystal calibrator using an inexpensive microprocessor crystal and CMOS IC's which are readily available at Radio Shack.
The main problem with building a 100Khz oscillator is the unavailability of 100Khz crystals. Even if you find a vendor willing to cut such a crystal for you, plan on paying $20 or more not including shipping charges. The circuit in Figure 1 uses an inexpensive 8Mhz microprocessor crystal which can be easily obtained from most parts suppliers for about $1. Using a 74HCT393 binary counter IC, we can easily divide down the 8 MHz signal from our crystal into 100Khz or almost any frequency we need.
The circuit in Figure 1 uses a couple of NAND gates (74HCT00 IC) for our 8Mhz crystal oscillator. Capacitor C2 actually helps us tune the crystal to the exact frequency, Use any value of C2 from about 22pf to about 82pf to get the oscillator on frequency. In the prototype, 68pf worked fine for most of the crystals tested. For an exact frequency, replace C2 with a 22pf and add a 50pf trimmer capacitor in parallel. By adjusting the 50pf trimmer capacitor, we can easily get the crystal exactly on frequency. The first NAND gate is our oscillator while the second NAND gate acts as a buffer and conditions the signal. This signal is then fed into the clock pulse input of one of the 4 bit binary counters in IC2. By taking the output from the Q3 signal, we have now divided the signal by 16 giving us 500Khz. This signal is now fed into the clock pulse input of the second 4 bit binary counter. In the first counter we tied the MR (clock reset) line to ground. In the second counter, we need the count to reset when we reach a binary five, which will allow us to divide the 500Khz by 5. For this counter, we used the last 2 remaining NAND gates in IC1 to detect the desired value. When we reach the correct reset interval, the MR line goes high resetting the counter to zero and allowing us to effectively divide by 5. The 100Khz output is taken from the Q2 line and is coupled through capacitor C4.
If you prefer, this circuit can be easily changed to a 50Khz calibrator by wiring pins 13 & 14 of IC1 into pins 10 and 8 of IC2. See Figure 2 for details. This arrangement makes the second counter reset at binary 10 which divides the 500Khz by 10 giving us the desired 50Khz.
The HCT series CMOS logic IC's require a 5 volt power supply just like the old TTL logic series. In this circuit we used a 5 volt zener diode, D1, along with resistor R2 to get 12 volts down to 5 volts. Capacitor C3 is used primarily for bypassing the oscillator and must be used in this circuit. If you prefer to power this circuit from a 9 volt battery, then reduce resistor R2 to 220 ohms for best performance.
If you plan to install this circuit inside a transceiver, feed the output directly to the receiver front end. Make certain you have connected it after the TR relay so that the circuit doesn't get zapped by RF from the transmitter side. Also, you will want to install an ON/OFF switch which will interrupt the 12V line going to the circuit. As with all static sensitive CMOS IC's, use special handling precautions and do not leave out those IC sockets.
This circuit has been found to generate accurate birdies at every 100Khz and will be an excellent aid in getting that old rig right on frequency. The accuracy of the 100Khz birdies will depend on how close the 8Mhz oscillator is on frequency. With the difficulty in getting crystals for specific frequencies, this circuit gives new meaning to the words "Divide and Conquer".
要產生100千赫茲頻率的電路，如果采用晶體管搭建的LC震蕩電路，當要求頻率很穩定時比較困難，而采用晶體震蕩器則容易實現，而低頻率的晶體震蕩器又不容易獲得，下面的電路就能夠?qū)㈩l率較高的晶體震蕩器通過適當?shù)碾娐份敵鲱l率較低的信號。
電路原理簡單，通過IC1的門電路，晶體以及外圍電路組成8M赫茲震蕩器，通過IC2分頻獲得100千赫茲信號。
DE N1HFX
下圖是產生50千赫茲的電路，13腳接上圖的IC2的6腳就可以了。
元件清單
Parts List
| C1
聲明：本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人，不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用，如有內容侵權或者其他違規問題，請聯系本站處理。
舉報投訴
發布評論請先 登錄 相關推薦
熱點推薦
英飛凌功率校正芯片ICE3PCS03G時具有最低的內部參考微調和集成的數字控制電壓環。它們還具有其他優點，如0.2V時的低峰值電流限制、21kHz至100kHz的可調柵極開關頻率范圍以及能夠與50kHz至100kHz之間的
發表于 04-30 17:09
針對高頻（100kHz）碳化硅NPC三電平UPS的不間斷電源諧波抑制與控制算法針對高頻（100kHz）碳化硅NPC三電平UPS的不間斷電源諧波抑制與控制算法綜合研究 1. 現代不間斷電源系統的高頻演進與三電平拓?fù)浼夹g(shù)背景 在現代數據中心、精密醫療裝備、工業自動化控制網絡以及
LTC5507：100kHz 至 1GHz RF 功率檢測器的技術剖析LTC5507：100kHz 至 1GHz RF 功率檢測器的技術剖析 在當今的電子設備中，RF 功率檢測是一項至關重要的技術，它廣泛應用于無線通信、雷達等領域。LTC5507 作為一款出色的 RF
LT3023：雙路100mA低噪聲微功耗穩壓器的卓越之選100mA低噪聲微功耗穩壓器——LT3023。 文件下載： LT3023.pdf 一、LT3023的核心特性 1. 低噪聲與低靜態電流 LT3023的輸出噪聲極低，在10Hz至100kHz帶寬內僅為20μVRMS。這一特性使得它在對噪聲敏感的應用中表現出色，如射頻
為什么時鐘都用32.768kHz晶振？優勢、應用、選型要點工程師、采購必看：RTC走時不準、功耗超標、批量溫漂大、選型反復踩坑，90%問題都出在32.768kHz晶振沒選對。它是時鐘、電表、藍牙、手環、工控主板的標準時基，搞懂原理、參數、封裝、避坑技巧，一次設計穩定量產，再也不用返工。
17V/3A低噪音高效率集成鐵氧體磁珠濾波器補償同步降壓轉換器 QFN10封裝。特性:? 低輸出1/f噪聲28.4μVRMS（100Hz至100kHz）@0.8V51.1μVRMS（100Hz至100kHz）@1.2V68.9μVRMS（
發表于 03-04 17:34
MLX90109 125kHz RFID 收發器：特性、應用與設計要點 MLX90109 是一款集成式 RFID 收發器，能夠?qū)ぶ?100kHz 至 150kHz 頻率范圍的應答器。它支持雙相和曼徹斯特 ASK 以及 ON/OFF 鍵控調制，具有低功耗
SiLM6478低邊MOSFET驅動器，支持3-60V輸入與100kHz-2.2MHz調頻高可靠性、高集成度的解決方案。特性
寬輸入電壓范圍：支持3V至60V輸入。
可調開關頻率：工作頻率可通過外部配置在100kHz至2.2MHz范圍內調節。
強大內置驅動：集成1.5A峰值電流的低邊柵極驅動器
發表于 01-30 08:22
SCT2430QSTER 高效率同步DCDC降壓變換器電路圖資料控制，支持脈沖跳躍調制（PSM），典型靜態電流低至 25μA，有助于轉換器在輕載或待機條件下實現高效率。SCT2430Q 通過外部電阻可實現 100kHz 至 2.2MHz 的可編程開關頻率，為優化效率或外部元件尺寸提供了靈活性。轉換器支持 100kHz 至 2.2MHz
發表于 01-27 16:29
?0次下載
MLX90109 125kHz RFID 收發器：設計與應用全解析 收發器 ：能夠?qū)ぶ?100kHz 至 150kHz 頻率范圍的應答器，支持雙相和曼徹斯特 ASK 編碼，以及 ON/OFF 鍵控調制。 低功耗高性能 ：采用獨特的
氮化硼軟陶瓷片 | 三高一阻新材料電源控制板（如開關電源、UPS、工業電源模塊等）的IGBT核心功能是實現電能的高效轉換與穩定輸出，其工作場景具有功率跨度大（10W~100kW）、開關頻率高（10kHz~
傾佳電子基于SiC MOSFET 的 3kW 高頻 (100kHz) CCM 圖騰柱 PFC 設計、分析與效率建模傾佳電子基于SiC MOSFET 的 3kW 高頻 (100kHz) CCM 圖騰柱 PFC 設計、分析與效率建模 傾佳電子（Changer Tech）是一家專注于功率半導體和新能源汽車連
請問如何確定和配置 HRPWM 周期值？你好，我想控制PWM開關頻率，精度為10MHz±1%（100KHz）。
PSoC? Control C3 可以為 PWM 外設提供 240MHz 時鐘。因此，通過設置 Period=24，PWM
發表于 08-12 08:24
XL4016是一個180 KHz的固定頻率 PWM降壓（降壓）DC/DC轉換器頻率振蕩器。PWM控制電路能夠調節占空比線性從0到100%。一個在內置電流保護功能。當短路保護功能發生時操作頻率將從180KHz到48KHz
發表于 07-01 15:18
?0次下載
32.768kHz：現代科技的時間命脈在晶振行業中，32.768kHz頻率的晶振是最常用的一種它是一款實時時鐘晶振能夠產生時序電路基準信號精確到一秒的計時因在頻率元器件領域無處不在而出名在日常生活中，時鐘隨處可見鬧鐘、手表
|
評論